Please wait...
×

Error

  • 2D groundwater flow and contaminant transport model in Unsaturated media

    hi every one
    i need for help please help me
    i have 2D model in unsaturated media and i have some question:

    1- For hydraulic head in flow initial, Do you use values for hydraulic head depend on groundwater table map or depend on values of moisture content.
    2- For boundaries if I can use head or flux depend on groundwater table, and can I use in boundary of mode or cover all elements of model.


    Thanks for every one
    With best wishes

    Yahia alwathaf
  • scenarios for the model

    hi Mr. Peter     
    I am now finished  simulation of model in transient state and the simulation period from 1972 to 2008.
    and now i want do scenario for model to 2025, and i have three scenarios:
    1- The first Scenario represents the present status based on the year 2008 . A simulation of this situation at the year 2025 was made whereby the predicted water balance components for 2020 were computed for the continued present rate of pumping, under the same present rate of groundwater recharge. So how do this step?
    2-The second Scenario simulates the effect of water augmentation i.e. the increase of groundwater recharge, With the stabilization of the rate of extraction of groundwater. So how do this step?
    3- The third Scenario simulates the effect of water extraction i.e. the increase of extraction of groundwater of groundwater recharge, With the stabilization of the rate of groundwater recharge. So how do this step?

    thank you very much   

    yahia alwathaf
    Morocco
    alwathaf@hotmail.com
    +212648022929
  • How do i scenarios for the model?

    hi every one  ;D ;D ;D
    I am now finished  simulation of model in transient state and the simulation period from 1972 to 2008.
    and now i want do scenario for model to 2025, and i have three scenarios:
    1- The first Scenario represents the present status based on the year 2008 . A simulation of this situation at the year 2025 was made whereby the predicted water balance components for 2020 were computed for the continued present rate of pumping, under the same present rate of groundwater recharge. So how do this step?
    2-The second Scenario simulates the effect of water augmentation i.e. the increase of groundwater recharge, With the stabilization of the rate of extraction of groundwater. So how do this step?
    3- The third Scenario simulates the effect of water extraction i.e. the increase of extraction of groundwater of groundwater recharge, With the stabilization of the rate of groundwater recharge. So how do this step?

    thank you very much :D :D :D

    yahia alwathaf
    Morocco
    alwathaf@hotmail.com
    +212648022929
  • drawdowns map

    hi Mr. Peter  :) :)
    the simulation of model in transient state is ok, but i have some questions about drawdowns map.
    I took a period of time for simulation of model from 1972 to 2008.
    so How do I show the map of drawdowns in model between these two periods

    thank you very much

    yahia alwathaf
  • Re: observation wells

    thank you very much Mr. Peter
  • observation wells

    hi foe all ;D ;D ;D
    hi Mr. Peter :)
    I have one question.
    Simulation of model in transient state is ok, but I have 25 observation wells.
    I know how enter this observation well to model, but how enter the Piezometric monitoring for each well  and how export this data for comparison between the Piezometric calculated and observer.
    Please help me and thank you for ever.

    yahia al wathaf
    Morocco
  • T-list2

    this message for Mr. peter 
    in the simulation of model in transient state, I had two problems:
    abstraction of water vs times is ok i make time  function ID for each well.
    but the problem now How I work time function for recharge because i have basin Consists of 22 sub-basin. and in T-list enter periods of time only, i want enter periods of time with Value of recharge  how?
    Because frankly, the example  is located in the users_manual are not clear enough
    please help me
    and thank you

    yahia alwathaf
    Morocco
  • Re: time stages

    thank you very much Mr. Peter
  • T-list

    hi every one  ;D ;D ;D
    now i do simulation of model in transient state and simulation is ok
    but i have some problem in T-list for material proprites, how enter the abstraction of water in function of time
    because i have basin Consists of 22 sub-basin. and in T-list enter periods of time only, i want enter periods of time with Value of abstraction how?
    please any one help me
    and thank for every one
  • time stages

    hi every one  ;D ;D ;D
    i have some queries about simulation of model
    the simulation of model in transient state is ok
    but i have some questions
    after simulation and show results show a one time stage in windwo of time stages file browser
    So how can I show multiple time stages ?

    in the end  thank for help
    yahia alwathaf